inknix

Clear production for screen and stage

← Journal
Studio Design

Studio Design Checklist: What to Settle Before You Commit

A working list of questions to put to your team and your designer before a television studio layout is fixed, from floor plan and cabling to control room sightlines and sound.

Daniel Whitcombe

6 minutes to read

Studio Design Checklist: What to Settle Before You Commit

Start with what the studio must produce

Before anyone draws a floor plan, write down the programmes the room has to carry. A morning magazine show with a sofa and a presenter desk asks very different things of a space than a single-camera drama or a two-person interview. List the formats, the number of people on set at once, and whether sets are built fresh each week or stay standing.

I come at this as a sound engineer, and the same questions shape what I will later ask of the room. Does the show need an audience? Will guests be miked or boomed? Will the studio be shared by several productions with different needs? A studio that is excellent for one format is often awkward for the next.

Put these answers on one page and circulate it to everyone who will use the room. Disagreements that surface at this point cost nothing. The same disagreements, found after the walls are up, cost a great deal.

  • Formats and typical running lengths
  • Maximum people on the floor at once
  • Fixed sets or frequent rebuilds
  • Audience, yes or no
  • Single production or shared use

Floor size, ceiling height and access

Measure the usable floor, not the room as described in a lease. Columns, radiators, fire exits and door swings all take space that a plan drawn from outside dimensions will quietly count as available. Ceiling height matters as much as area, because lighting grids, cyc walls and camera cranes all need clear vertical room, and low ceilings trap heat.

Then look at how things get in. Scenery, flight cases and pedestal cameras need a route from loading area to floor without being taken apart. A doorway that is ten centimetres too narrow can decide how a studio is used for years.

Finally, check floor flatness and load. Camera pedestals glide badly over uneven concrete, and a grid hung from a structure that was never rated for it is a risk no schedule excuses. Ask for a structural opinion in writing before you plan anything heavy overhead.

  • Usable floor after columns and exits
  • Clear height under the lighting grid
  • Route from loading bay to studio floor
  • Floor flatness for pedestal moves
  • Structural rating for hung equipment

Cabling, power and noise from the building

Cabling is the part of a studio nobody photographs and everybody depends on. Decide early where the wall boxes go, how many circuits of video, audio, intercom and data each one carries, and whether you want spare capacity. Cable that is cheap to pull during construction is expensive to add afterwards, so allow room in containment for growth.

Keep power and signal apart wherever the layout allows. Mixed runs invite hum in audio and interference in video that takes days to trace. Talk to the electrician about clean supplies for the control room and separate feeds for lighting dimmers.

From my side, I would add the building itself. Air handling, lifts, traffic outside and neighbouring rooms all leak into microphones. Stand in the empty space, in silence, and listen for a few minutes. What you hear now, the microphones will hear later.

  • Wall box positions and circuit counts
  • Spare capacity in cable containment
  • Separation of power from signal runs
  • Clean supply for the control room
  • Ventilation noise and outside intrusions

Control room position and sightlines

The control room should see the studio floor, or at the very least have monitoring good enough that nobody misses it. Where there is a window, check what it shows from each seat: the director, the vision mixer and the sound desk all need a view of the set, not of each other's backs.

Think about how many people sit in there on a busy day. Director, assistant, vision mixer, graphics, sound, producer and sometimes a guest producer add up quickly. Desk depth, chair space and walking routes should be drawn at full size, ideally taped out on the floor of an empty room before anything is ordered.

Acoustic separation matters in both directions. The floor should not hear the gallery talking, and the gallery should not be confused by studio noise coming through a thin partition. Ask what the wall and glazing are rated for, and ask for it in writing.

  • Window view from every operating seat
  • Desk depth and seating for a full crew
  • Taped-out layout before ordering
  • Sound rating of walls and glazing
  • Clear route between gallery and floor

Lighting, sound and camera positions together

Lighting, sound and cameras compete for the same space above and around the set, and the usual mistake is to plan each in isolation. A microphone boom needs a path that avoids lamp shadows. A camera move needs clear floor that cable runs must not cross. Draw all three on the same plan and walk through a typical show shot by shot.

Check grid coverage against the set positions you listed at the start, not against an abstract rectangle. Lamps that reach the sofa but not the standing area will force a rig change every time the show shifts. Leave some flexibility in rigging points and in the number of dimmer channels.

Talk to the camera and lighting colleagues before the plan is final. An hour of conversation with the people who will operate the room finds problems that no drawing can show, and it is far cheaper than moving a grid bar once it is bolted.

  • One shared plan for lights, sound and cameras
  • Boom paths clear of lamp shadows
  • Grid coverage matched to real set positions
  • Spare dimmer channels and rigging points

Budget, phasing and who signs off

Decide which parts of the studio must exist on opening day and which can follow. Cabling containment, acoustic treatment and structure are best done once, in full. Extra cameras, additional lamps and secondary monitoring can be added later without disturbing the walls.

Agree who signs off each stage. A studio plan touched by programme makers, engineers, facilities staff and finance can drift for months if nobody has the last word. Name one person for decisions and keep a short written record of what was agreed and when.

Ask for a clear handover: as-built drawings, cable schedules, equipment lists and operating notes. These are dull documents and they are the ones you will reach for in three years when something stops working and the people who built it have moved on.

  • Work to do once versus work that can follow
  • One named person for final decisions
  • Written record of each agreed change
  • Handover drawings, cable schedules and notes

A studio is a long commitment, and most of what makes it good or bad is settled before any equipment arrives. Go through these questions with your whole team, put the answers on paper and test them against a real show. If something stays unclear after that, it is worth a conversation with whoever will design and build the room, while changes are still cheap.