Planning a Live Sound Setup: A Practical Guide for First-Time Producers
A step-by-step guide to planning front of house and monitor mixing, tuning a system to a room and preparing clean audio feeds for broadcast partners.
6 minutes to read

Start with the room and the audience
Every sound plan begins with two questions: where will people stand or sit, and how many of them are there? A narrow hall with a low ceiling behaves very differently from a wide marquee, even when the same speakers are used. Walk the space before anything is specified, clap your hands, and listen to how long the sound lingers. Hard walls and glass give long tails that smear speech, while soft furnishings and a full audience soak up energy.
Note the practical limits too: where the mixing position can sit, how far the cable runs are, where power is available and whether any part of the audience is tucked behind a pillar or under a balcony. These details decide how many speaker positions you need and whether delay stacks are required at the back.
Write all of this down on one page before talking to suppliers. A short sheet with room dimensions, capacity, surfaces and access times lets a sound engineer quote accurately and spares everyone surprises on load-in day.
- Room dimensions and ceiling height
- Expected audience size and layout
- Mixing position and cable routes
- Power supply and load-in access
Choose the front of house system with care
The front of house system is what the audience hears, and it should be chosen for coverage first and loudness second. Even coverage means the person at the back hears roughly what the person at the front hears, without the front row being deafened. For speech-led events, clarity matters more than low-end weight, so a modest system placed well often beats a large one placed badly.
Ask your engineer how the speakers will be hung or stacked and where the coverage ends. Speakers pointed at reflective walls cause echo, so aim them at the audience and keep them away from open microphones where possible.
Discuss subwoofers separately. Music events benefit from them, but a conference or panel usually does not, and leaving them out simplifies the rig, reduces cost and keeps the room tidy.
Monitor mixing: giving performers what they need
Monitors are the speakers or in-ear systems that let performers hear themselves, and a poor monitor mix is the quickest way to an uncomfortable show. A singer who cannot hear the band will push too hard, drift out of tune or step away from the microphone. A good monitor engineer asks each performer what they need and builds the mix around that rather than guessing.
Agree the number of separate monitor mixes early, because each one needs its own channel of amplification and its own set of controls. A five-piece band may want five different mixes, while a speaker on a lectern needs only a single wedge angled upwards.
Allow time at soundcheck for each person to say what is missing. Small changes, such as a little more vocal or less guitar, take seconds to make and prevent problems for the entire performance.
- Count the separate mixes required
- Decide between wedges and in-ear systems
- Reserve soundcheck time for each performer
Tuning the system before the doors open
System tuning is the work of making the speakers sound right in this particular room. The engineer plays test signals, measures the response with a calibrated microphone and adjusts equalisation and speaker timing so that the sound is balanced and the sources line up. Without it, even good equipment can sound boomy or harsh.
Tuning needs an empty room and some quiet. Schedule it before rehearsals and before other crews begin hammering, drilling or testing lights, otherwise the measurements are unreliable and the engineer ends up working by ear alone.
Finish with a listening walk. Play familiar music or speech and move through the audience area, checking the front, the sides, the back and any awkward corners. Adjust only what you actually hear, and keep notes so the settings can be restored if something is accidentally changed.
Audio feeds for broadcast partners
When an event is also being recorded or sent to a television network, the broadcast team needs a clean audio feed that is separate from what the room hears. The house mix is shaped for people in the venue, so it often contains too much bass, too little ambience and uneven levels when sent elsewhere.
A better approach is a dedicated broadcast mix, either taken from a split of the microphones or created on a second desk. Agree this early with the receiving team and confirm the format: balanced analogue lines, digital connections and the sample rate they expect.
Label every line clearly, test the feed with the receiving engineer before the event and keep a spare route available. A short call between the two sound teams at the start of the day resolves most misunderstandings long before anything goes live.
- Confirm connection type and sample rate
- Label every feed at both ends
- Test with the receiving engineer in advance
A simple order of work for the day
On the day, a calm sequence saves time. Load in and place the speakers first, then run power and signal cables, then switch on and check every channel before anyone starts to tune. Performers arrive only once the room is stable, so soundcheck can be quick and focused.
Keep one person responsible for decisions. Where several people each ask for a small change, the mix drifts and nobody knows why. A single point of contact, usually the front of house engineer, keeps requests orderly and makes it clear who to speak to.
After the event, take a few minutes to write down what worked and what did not. Those notes become the starting point for the next plan, and over a season they turn into a dependable checklist for your team.
Good live sound comes from preparation more than equipment. Know the room, choose a system for coverage, build monitor mixes around the performers, tune before the audience arrives and treat broadcast feeds as their own job. In these colder months, when halls are busy with seasonal events, a clear one-page plan shared early with every crew will save time, avoid avoidable faults and let everyone concentrate on the performance itself.