Lighting Plans That Go Wrong: Six Mistakes and How to Avoid Them
Most problems on a lit stage start long before the rig goes up. Six recurring mistakes in event lighting, from missing site details to rushed focus time, and the habits that prevent them.
7 minutes to read

Designing before anyone has seen the room
The most common mistake I meet is a lighting plan drawn from a floor plan and a few photographs. A drawing cannot tell you that the ceiling of a converted hall sags by forty centimetres at one end, that a beam hides the only sensible hang point, or that the loading door is narrower than the road cases. Every one of those facts changes the rig.
A site visit does not need to be long. An hour with a tape measure, a torch and the venue manager usually settles ceiling height, rigging points, power supply, distance from the loading bay to the stage and where the audience will actually stand.
Record what you find in writing and send it to everyone involved. When the lighting designer, the production manager and the venue all work from the same measurements, disagreements surface in a calm email rather than at nine in the morning on the day of the show.
- Measure the real trim height, not the figure in the venue brochure
- Photograph every rigging point and the route in from the loading bay
- Ask who owns the power distribution and who may connect to it
Treating power and rigging as someone else's problem
A lighting design is only as good as the power that feeds it and the structure that holds it. Plans fail quietly here: a designer specifies a generous number of moving heads, nobody adds up the load, and on the day the venue supply trips as the first full look is brought up.
Do the sum early. List every fixture with its wattage, group them by circuit, and leave headroom rather than running a supply near its limit. If the load is high, say so in the plan and agree the supply with the venue well ahead.
Rigging deserves the same care. Truss, hoists and points all carry rated loads, and the total of fixtures, cabling and any scenic items hung from the same structure must sit inside them. A rigging document written for each job, with weights and hang positions, is not paperwork for its own sake. It is what lets a crew rig safely and lets a venue say yes.
- Total the load per circuit and keep clear headroom
- Weigh fixtures, cable and scenery together when checking rig loads
- Share the rigging document with the venue before load-in
Ignoring the camera when the show is filmed
Lighting that looks warm and atmospheric to the eye can look muddy, flat or harshly contrasted through a lens. When a concert or festival set is being recorded or broadcast, the camera becomes a second audience with different needs, and a plan written only for the room will disappoint it.
Talk to the camera and vision teams before the design is fixed. Ask where the cameras will stand, which lens lengths they expect, and how much key light the faces need. Stage washes that are fine for the front row may leave a singer in shadow on a long lens.
Flicker is another trap. Some fixtures, particularly cheaper LED units, can show banding on camera at certain shutter settings. A short test in front of a camera during the technical run costs ten minutes and spares everyone a problem in the edit.
- Agree camera positions and lens lengths before finalising the plan
- Check key light on faces from the camera position, not the stalls
- Test LED fixtures on camera during the technical run
Leaving too little time to focus and program
Schedules are written around the doors time and the soundcheck, and lighting is often given whatever is left. Yet focusing every fixture and building the cues takes real hours, and it cannot be hurried without consequences. Lights pointing a little off look careless, and cues written in a rush tend to be rewritten during the show.
Ask your designer how long focus and programming genuinely need for the size of the rig, then protect that time in the schedule. Where possible, keep the stage clear of other work while lamps are being focused, since a musician setting up a drum riser under a moving ladder helps nobody.
Pre-visualisation helps too. If cues can be roughed out from the plan in advance, the time in the venue is spent refining them rather than starting from a blank desk. Even so, the rig has to be seen in the actual room before anyone trusts it.
- Ask for a focus and programming estimate in writing
- Keep the stage clear during focus
- Rough out cues in advance, then refine them in the venue
Skipping documentation and handover
Once the show is over, the lighting plan often vanishes into someone's laptop. The next team, whether a touring crew or the venue's own technicians, arrives with nothing to read and starts from scratch. It is a waste that is easy to prevent.
A useful handover is short: the final plan with fixture positions and addresses, a patch list, the cue list or desk file, and notes on anything that behaved oddly. Add the rigging document and the power figures, and label everything with the event and the version.
Include the small lessons as well. If a particular position needed a longer clamp, or the house lights could not be dimmed from the desk, write it down. Notes like these make the second event noticeably smoother than the first, and they are the difference between a rig that is repeated and one that is rebuilt from memory.
- Keep one current plan, patch list and desk file together
- Label every document with the event and version
- Record the small faults and fixes found on the day
Planning for the weather and the audience, not just the stage
In mid autumn, outdoor and marquee events bring their own risks. Damp air, early darkness and wind all change how a rig behaves. Fixtures that are not rated for rain need cover, cable runs need protection from standing water, and a tall structure needs a clear wind limit agreed in advance with the person who has the authority to call a halt.
Think about the audience as well. A bright beam aimed across the crowd tires eyes quickly, and a haze level that suits a rock set can make a speech unreadable. Walk the floor during the technical run and look at the stage from where people will stand, not only from the desk.
Finally, keep a plan for the evening running late. Dusk arrives earlier each week, and a show that starts in daylight may finish in the dark, so the lighting needs to work across both rather than only at the hour it was designed for.
- Check each fixture's weather rating and protect cable runs
- Agree a wind limit and who decides to stop
- View the stage from the audience position before doors
None of these mistakes is exotic, and none needs a large budget to avoid. They come from deciding too early, checking too little and writing too little down. Visit the room, add up the power, think about the camera, protect the focus time and leave a handover behind. A calm, documented plan is what makes a lit event look effortless, and what lets the crew enjoy the show too.