How We Mix Front of House and Monitors for Broadcast Partners
A look at how we run front of house and monitor mixing, tune the system before doors open, and send clean audio feeds to broadcast partners during late autumn events.
6 minutes to read

Two mixes, one room
Live sound for an event that is also being broadcast means serving two audiences at once: the people standing in the room and the viewers or listeners who will only ever hear the feed. We treat these as separate jobs from the first conversation. The front of house mix is built for the space, its reflections and its audience. The broadcast feed is built for headphones, television speakers and a network's loudness limits.
Keeping the two apart saves arguments later. A mix that sounds exciting in a large hall can sound harsh and cluttered when sent straight to air, and a clean broadcast balance can feel thin to a standing crowd. I plan both from the running order, so that each has its own console layer, its own metering and its own person responsible for it when the event is large enough to need that.
Front of house: mixing for the room
At front of house, my first task is to understand what the room does to sound. Late autumn venues are often fuller of coats, damp and heating noise than the same hall in summer, and a space that rang in rehearsal can feel drier once the audience arrives. I leave headroom for that change rather than chasing it with heavy equalisation during the first number.
The mix itself follows the programme. Speech-led shows need intelligibility above everything, so we pay attention to microphone choice, gating and the way a presenter moves around the stage. Music-led events need clarity between instruments before they need volume. I write down the starting settings for every act so that a changeover takes minutes and nobody is guessing at a fader position.
- Walk the room before doors and listen from several seats
- Leave headroom for an audience that absorbs sound
- Record starting settings for each act or speaker
Monitor mixing: what the performer needs to hear
Monitors are about trust. A performer who cannot hear themselves will push harder, move closer to the microphone and fight the system, and the front of house mix suffers for it. We ask performers early what they need: their own voice, a click or backing track, one other instrument, or very little at all.
Wedges, in-ear systems and side fills each have their place, and the choice depends on the stage size, the number of performers and how much spill the front of house can tolerate. In-ears reduce stage volume and help a broadcast pick-up considerably, but they isolate the wearer, so we usually add a little ambient microphone signal. A dedicated monitor engineer is worth the cost once more than a handful of mixes are in play.
- Ask each performer what they need before soundcheck
- Keep stage volume low where a broadcast pick-up is planned
System tuning before the first sound check
Tuning the loudspeaker system comes before any mixing. We measure the room, check that every cabinet is wired the right way round, set delays between main speakers and fill points, and listen to a reference piece we know well. This takes time, and it is the part of a live sound job that is easiest to cut when a schedule is tight and hardest to recover from afterwards.
The aim is an even response across the audience area, not a perfect curve on a screen. We walk the seating, including the awkward corners under balconies, and adjust until the extremes are acceptable. A system that is well aligned needs less correction at the console, which leaves the mixing engineer free to follow the performance rather than rescue it.
Audio feeds for the broadcast side
The feed that leaves the building is agreed in writing with the broadcast partner well ahead of the event. We confirm the format, the number of channels, the level at which the feed is delivered and where the connection is made. A short document from our workflow producer sets out these points, so the audio team on the truck or in the gallery is working from the same plan as we are.
We prefer to give broadcast partners a feed taken from a dedicated mix rather than a copy of the front of house output. That allows ambient microphones, presenter talkback and music to be balanced for television instead of for the hall. During rehearsal we send a test signal and ask the receiving team to confirm what arrives, then agree how they will speak to us if something drifts during the show.
- Agree format, channel count and level in writing
- Send a test feed during rehearsal and confirm receipt
- Use a dedicated broadcast mix instead of a copy of the room mix
What to settle with us before the event
Most live sound problems we are called in to fix began as questions nobody asked early. Before an event we like to know the venue and its rules on noise, the running order, the number of speakers or performers, any recorded playback, and what the broadcast partner expects to receive. Even rough answers let us propose a sensible system and crew.
We also ask about load-in times, power and cable routes, because a good plan on paper still depends on being able to rig on the day. If a venue has not been used for sound before, we visit in advance. For smaller jobs a detailed call and a floor plan can be enough. Either way, you receive a written outline of who is mixing what and who to call if something changes.
- Venue, noise limits and access times
- Running order and number of performers or speakers
- What the broadcast partner expects to receive
Good live sound for broadcast comes down to preparation and plain agreement between people. Separate the room mix from the broadcast feed, tune the system before mixing, give performers what they need to hear, and write down what is being delivered and to whom. If you are planning an event for the coming weeks, contact us through the contact page with the venue and running order, and we will outline what the sound side needs.