inknix

Clear production for screen and stage

← Journal
Customer case

A village hall wedding, a thin power supply and a lighting plan that held

Priya Nair recounts how a couple's planned evening reception in a draughty hall called for a careful lighting plan, from the first site visit to the last cable coiled away.

Priya Nair

6 minutes to read

A village hall wedding, a thin power supply and a lighting plan that held

The first call from Marianne

Marianne rang us in the first weeks of the colder season. Her daughter was to be married in a converted barn used as a village hall, and the family wanted the evening reception to feel warm and a little theatrical without looking like a nightclub. She had already been told by one supplier that the hall could not take a proper rig. Her question to me was simple: is that true, or is it just easier to say no?

I do not answer that kind of question over the phone. A hall is only a room until someone has measured the ceiling, found the sockets and walked the route from the van to the stage end. I booked a site visit for the following week and asked her to have the caretaker there with the keys and any notes on the electrics.

Before I hung up I asked three things: how many guests, when the dancing would start, and whether anything was to be filmed. The answers shaped everything that followed.

What the site visit showed

The barn had a beautiful vaulted roof and almost nothing to hang from. The beams were old, and the caretaker was firm that nothing should be drilled or clamped to them. The power was the second surprise: one modest supply feeding the kitchen, the heating and the sockets on the stage wall, all on shared circuits.

I spent most of the visit with a tape measure and a torch. I noted the beam spans, the height of the lowest point where guests would stand, the position of the fuse board and which sockets shared a circuit. I also stood where the top table would be and looked at where a camera might sit, because a lit room that cannot be filmed well is a poor result for a family.

None of this ruled the hall out. It simply meant the plan had to start from what the building would allow rather than from a wish list.

  • Beam positions and safe fixing points
  • Circuit layout and total available load
  • Lowest ceiling height over guests
  • Distance from loading door to the dance floor

Designing around the limits

With no overhead fixing, I proposed two freestanding lighting stands at the stage end, plus floor-level fittings along the side walls to wash the old brickwork in a warm tone. LED fixtures kept the electrical draw low enough to sit within one dedicated circuit, with the kitchen and heating left alone on their own.

I drew the plan on one page: where each stand would sit, where each cable would run, which sockets were used and what the total load came to. I also wrote a short list of scenes. Dinner would be a soft amber wash, speeches a plain warm light on the top table, and the dance floor a slow build with colour added only after the first few songs.

Marianne read it twice and asked one good question: what happens if a fuse trips halfway through the evening? We agreed a reduced backup scene that could run from a second circuit, and I marked the fuse board clearly for the caretaker.

Rigging day and the cable problem

We arrived mid-morning on the day before the wedding. The stands went up first, weighted and checked for stability on the uneven stone floor. Then came the cables, which in a hall like this are the real hazard. Guests carry drinks, children run and heels catch on anything raised.

We ran side-wall cables along the base of the brickwork and covered every crossing with proper ramps. Where a cable had to cross the walkway to the cloakroom, we rerouted behind the stage curtain instead, adding some metres but removing the risk altogether. Every connection was labelled to match the drawing.

In the afternoon we ran each scene with the caretaker watching. I turned on the full dance-floor look, left it for twenty minutes and checked the temperature of the fixtures and the supply. Nothing struggled, and the fuse board stayed quiet.

The evening itself

I do not attend every event, but for this one I stayed in the corner for the first hour. The amber dinner light made the brickwork glow, and several guests commented on how warm the room felt, which is exactly what Marianne had asked for. The speeches were easy to see and easy to photograph.

When the dancing began, the colour came in slowly as planned. The first few songs were under plain warm light, and only then did the side walls shift to deeper tones. Nobody noticed the change happening, which is how a good transition should work.

There was one small moment: a guest knocked a floor fitting, and it tilted. The caretaker, who had been shown how to reset it, fixed it in seconds. That is the kind of detail a written plan is for.

What I took from the job

The first supplier had not been wrong that the hall was awkward. They had simply stopped at the awkwardness. A fixed set of limits, once measured, becomes a design brief rather than a refusal.

I also took away how much the caretaker's knowledge helped. The location of a spare circuit, the habit of the heating tripping in the cold and the best door for the van were all things he knew and no drawing showed.

Marianne sent a short note afterwards saying her daughter had not once thought about the lights, which I took as the best possible review. A lighting plan is working when the room simply feels right.

A modest hall, a thin power supply and a tight brief turned out to be a good reminder that lighting begins with measuring, not with equipment. Walk the room, learn its limits, draw a plan the caretaker can read and test every scene before the guests arrive. If you are planning an evening event in a venue that others have called difficult, bring the keys, the electrics notes and your list of scenes.